I-Bullet

Bullet Charger Series

IMG_9329.JPG

The I-Bullet charger is a low-cost, stand-alone unit designed for use with strings of 1 to 4 lithium ion cells or 1 to 14 nickel metal hydride cells. The nominal charge current is factory set to 1000mA, though other values are available on a special order basis. The unit has a universal input for worldwide use and a standard 6-foot output cable. Lithium ion versions are terminated in a 2.5mm DC plug while the nickel metal hydride version is terminated in bare wires. Other options are also available.
When used with lithium ion cells, the I-Bullet can simultaneously charge a cell string and power a piece of host equipment, provided that the equipment draws less than 500mA nominally. This allows the I-Bullet to be permanently attached to the host product and act as its sole power source. The charging process will restart as needed to keep the cells full. When the cells are full, current is terminated in order to promote long cell life.

 

Target Batteries: 

Lithium Ion, Lithium Polymer, Nickel Metal Hydride, Nickel Cadmium, Lead Acid


Specifications

General

Charge Current
1000mA
(660mA for IB-16800)
Voltage Limit Preset
Termination Current C/10
Input voltage 90VAC to 240VAC
Output connector
Right angle barrel connector
(2.5mm DC)
Connector Barrel Length 0.35” (9mm)
Cable
72”-80”
(183cm - 200cm)

Physical and Environmental

Dimensions
2.95” x 2.00” x 1.56”
(75mm x 51mm x 40mm)
Weight 5oz (135g)
Material Black ABS GSM
Battery Bay Geometry Various Available
Storage Temperature -20°C to 85°C
Humidity 15% to 95% (Non-Condensing)

LED Indications

Off No battery detected
Single Green Flash Power Up
Green Flashing Fast charging
Green Solid Fully Charged

Input Supply

Input voltage 90VAC to 240VAC
Frequency 50Hz to 60Hz
North America / Japan wall plug Built In Flip-Out Blades
Europe Wall Plug Adapter Available
United Kingdom Wall Plug Adapter Available
Australia/New Zealand Wall Plug Adapter Available

International Adapters for I-Bullet Charger

From Left to Right:

IB-ADP-A00 - This is an adapter for the I-Bullet for use in Australia

IB-ADP-0E0 - This is an adapter for the I-Bullet for use in Europe

IB-ADP-00U - This is an adapter for the I-Bullet for use in only the UK

Standard Output Cable

Length
72”-80”
(183cm - 200cm)
Red Wire Positive battery lead
Black wire Negative Battery Lead
Green Wire
Thermistor lead
(Used Only with NiMH and NiCd)
White Wire
Remote LED
(Used Only with NiMH and NiCd)
Output Connector 2.5mm (Center Positive)

Battery Charger Interaction Specifications

Battery Chemistry Lithium Ion NiMH NiCd Lead Acid Timed
Termination Algorithm CCCV
dT/dt
(Thermistor required)
Negative delta V CCCV Timer
Applicable Range N/A Capacity/3 to 3x Capacity Capacity/3 to 3x Capacity N/A < Capacity/6
Termination Value/Point Current Falls to Limit Value/5 dT/dt or -delta V dT/dt or -delta V Current Falls to Limit Value/5 Customer Specified
Top-off Charge 1 Hour or Current Falls
to Limit Value/10
100mA for 1 hour
after termination indicate
100mA for 1 hour
after termination indicate
N/A N/A
Trickle Charge N/A Continuous at C/300 Continuous at C/300 Float Continuous at C/300
Charge Current Limit Customer Specified Customer Specified Customer Specified Customer Specified Customer Specified
Charge Voltage Limit Preset to 4.20V/cell up to 16.8V N/A N/A Customer Specified Customer Specified
Override Timer None 4 Hours 4 Hours None Customer Specified
Restart Threshold
7/8 of Termination Voltage
or Every 2 Hours
N/A N/A 7/8 of Termination Voltage N/A
Number of Cells 1 to 4 1 to 14 1 to 14 2 to 12 2 to 20

Agency Certifications

CE.jpg
Lead Free.jpg
 

Kit Contents

Standard Kit Contents

Charger
Instruction Sheet

Optional Components

Plug Adapters